Join Our Mailing List!

* required

*

*




Email Marketing by VerticalResponse

 Burns Tools BBB Business Review

10" 3HP 230V Professional Cabinet Saw with 36" T-Glide fence system, rails & extension table



Bookmark and Share

$2899.00
Add Item to Your Shopping Cart

SawStop PCS31230-TGP236 - 10" 3HP 230V Professional Cabinet Saw with 36" T-Glide fence system, rails & extension table

SawStop table saws are the most advanced saws in the world, setting the standard for table saw safety.

SawStop saws are equipped with a safety system that detects when someone accidentally contacts the spinning saw blade, and then stops the blade in milliseconds. In most cases, such an accident would result in just a nick on a SawStop saw, instead of the devastating injury which would likely occur on an ordinary table saw.

The system induces an electrical signal onto the blade and then monitors that signal for changes. The human body has a relatively large inherent electrical capacitance and conductivity, which cause the signal to drop when a person contacts the blade. Wood has a relatively small inherent capacitance and conductivity and does not cause the signal to drop.

The electrical signal drops quickly when the blade touches the finger. When the detection system sees dips like these, it knows a person has touched the blade.

In order to stop the saw, a fast-acting brake stops the blade when contact is detected. The brake includes a heavy-duty spring to push a block of aluminum, called a brake pawl, into the teeth of the blade to stop the blade from spinning. The spring is held in compression by a fuse wire until contact is detected. When contact is detected, the system sends a surge of electricity through the fuse wire to burn the wire and release the spring. The spring pushes the brake pawl into the teeth of the spinning blade, and the teeth cut into the aluminum and bind, thereby stopping the blade. All this happens in about 3–5 milliseconds, or 1/200th of a second. At the same time, the angular momentum of the blade causes the blade to retract below the table and the power to the motor is shut off.

The aluminum brake pawl pivots into the teeth of the blade. The brake pawl is part of a replaceable cartridge that includes the spring, fuse wire and electronics necessary to burn the fuse wire. An optional dado cartridge provides the same protection for dado cuts.

The standard and dado brake cartridges are single-use components that must be changed if the brake is ever activated. Changing a brake cartridge is fast and easy, no more complicated than changing the blade.

A safer, better saw, in so many ways.
The SawStop® Professional Cabinet Saw has several features to help operators stay safe.

  • SawStop safety system prevents serious injury with always-on protection.
  • 220V, 3.0HP model is engineered for the avid hobbyist and discerning professional
  • Dust Collection Blade Guard (included with the 3.0HP model, optional for the 1.75HP model). This innovative blade guard collects above-table dust and features independent lateral sides to minimize exposure to the blade. It retains a low profile to allow for cuts as narrow as 3/4 of an inch.
  • Riving knife minimizes kickback and provides protection during non-through cuts.
  • We double-check the saw every time you turn it on. A diagnostic self-check runs when you start the saw to ensure all systems are ready to detect an accident. If any problem is detected, the system will not allow the saw to start.
  • Sometimes you have your hands full and really need to stop the blade. Our large start/stop paddle with hands-free shutoff can be pushed with your knee allowing you to safely stop the blade even hands free.
  • Never worry again about someone using your saw when you’re not around. The main power switch with lockout key prevents unauthorized users from operating the saw.
  • When the power goes out, the saw stays off. The safety system won’t allow the motor to restart automatically when the power comes back on.
  • Left-tilting blade helps prevent wood from binding against the fence.
  • 10” Professional Cabinet Saw with 36” T-Glide fence system, rails & extension table
  • Heavy-duty arbor & arbor bearing
  • Contact detection & braking system
  • Cast-iron table, wings, trunnions and arbor block
  • Miter gauge with T-slots
  • European-style riving knife
  • Dust collection blade guard with splitter and
  • anti-kickback pawls
  • Blade shroud dust collection
  • Tool Free Zero-clearance insert
  • Quality 40 tooth carbide tip blade
Overall saw dimensions: 44" w x 29 3/4" d x 34" h

69 1/8" w x 33" d x 34" h (w/ T-Glide Fence System & 36" rails)

Motor:

3 hp, 1 phase, 230 V, 13 A

Weights: 426 lbs (with T-Glide Fence System & 36" rails)
Shipping weight (approx.): 390 lbs (table saw only)
Max. rip, right of blade: 30" (with optional 30" rails)
Cabinet footprint: 19 3/8" w x 19 3/8" d
Cast iron table: 20" w x 27" d, 44" w x 27" d (w/ extension wings)
Extension wing: 12" w x 27" d
Extension table (optional): 23 3/4" w x 27" d (36" rails), 40 1/8" w x 27" d (52" rails)
Blade: 40-tooth, professional grade, 5/8" arbor
Blade diameter: 10"
Blade tilt: Left
Blade kerf: 0.118" (3mm)
Blade plate thickness: 0.078" (2mm)
Max. depth of cut, blade at 0º: 3 1/8"
Max. depth of cut, blade at 45º: 2 1/4"
Max. rip, left of blade: 12"
Dado diameter: 8" (requires a separate brake cartridge and table insert)
Dado max. width: 13/16"
Arbor diameter at blade: 5/8"
Main bearing size: 62mm OD x 30mm ID
Second bearing size: 52mm OD x 25mm ID
Table in front of blade (max. elevation): 10 1/4"
Table behind blade (max. elevation): 7 1/2"
Arbor runout: 0.001" Maximum allowable runout
Blade lateral movement over full elevation range: 0.006" Maximum
Table flatness measured diagonally: 0.010" Maximum gap
Overall table and extension wing flatness: 0.025" Maximum gap
Blade alignment with miter slot: 0.010" Maximum displacement
Deviation of miter gauge indexing stops from actual: ±0.25º
Alignment between spreader and blade: 0.010" Maximum difference
Miter slots: T-shaped, 3/4" at top, 1" at bottom, 3/8" deep
Dust collection port diameter: 4"
Riving knife / splitter thickness: 0.078" (2mm)
Blade guard: polycarbonate, extends only 5/8" to right of blade
Insert: zero clearance, steel core, ABS surfaces
Hand wheels: 7" diameter, cast iron with chrome handle
Belts: 2 V-ribbed belts – arbor belt is static dissipative

 

 
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   

SawStop warrants to the original retail purchaser of a new contractor saw from an authorized SawStop distributor that the saw will be free from defects in material and workmanship for ONE YEAR from the date of purchase. SawStop warrants to the original retail purchaser of a refurbished, demonstration or floor model contractor saw from an authorized SawStop distributor that the saw will be free from defects in material and workmanship for SIX MONTHS from the date of purchase.

This warranty does not apply to defects arising from misuse, abuse, negligence, accidents, normal wear-and-tear, unauthorized repair or alteration, or lack of maintenance. This warranty is void if the saw or any portion of the saw is modified without the prior written permission of SawStop, LLC, or if the saw is located or has been operated outside of the country where the authorized SawStop distributor from whom the saw was purchased resides.

Please contact SawStop to take advantage of this warranty. If SawStop determines the saw is defective in material or workmanship, and not due to misuse, abuse, negligence, accidents, normal wear-and-tear, unauthorized repair or alteration, or lack of maintenance, then SawStop will, at its expense, and upon proof of purchase, send replacement parts to the original retail purchaser necessary to cure the defect. Alternatively, SawStop will repair the saw provided it is returned to SawStop, shipping prepaid, with proof of purchase and within the warranty period.

SawStop disclaims any and all other express or implied warranties, including merchantability and fitness for a particular purpose. SawStop shall not be liable for death, injuries to persons or property, or incidental, consequential, contingent or special damages arising from the use of the saw.

This warranty gives you specific legal rights. You may have other rights, which vary from state to state.

 

No Warranty of Safety

It is important to understand that SawStop® saws do not prevent injuries. They work to minimize the severity of injuries. In fact, an injury must occur before the SawStop® safety system reacts. The severity of the injury will depend on the speed at which a person contacts the spinning blade. You may incur a serious injury on a SawStop® saw. If you decide to use the saw in Bypass Mode, the safety system will be disabled and it will not activate in the event you contact the spinning blade.

Related Products:

MB-IND-000 Hydraulic Mobile Base SawStop
SawStop 10" Blade Brake Cartridge for ICS, CNS & PCS saws
SawStop 8" Dado Brake Cartridge for ICS, PCS & CNS saws
OFT30-CNS-000 30" Outfeed Table for SawStop CNS & PCS
MB-PCS-000 Mobile Base for PCS SawStop
MB-IND-500 To use ICS Mobile Base w/PCS
TSI-SLD Standard Lock-Down Insert NEW
TSI-DLD Lock-Down Dado Insert NEW
TSA-ODC Over-Arm Dust Collection Arm
All Rights Reserved © Burns Tools 2011